PremiumLine frostprotected heated eye-/face wash unit with bowl and lid
Frost-proof heated eye showers from B-SAFETY are equipped with a self-regulating trace heating cable and additional insulation. An integrated thermostat additionally secures the heating. The eye shower is covered from the outside with stainless steel sheets. This ensures maximum durability even in harsh industrial environments. The modular design with bolted valve covers ensures easy access to valves and connecting parts for maintenance. Freezing of these showers is not possible even under the most extreme conditions.
- Material: ABS plastic, stainless steel, brass
- Colour: white
- Total height: 1245 mm
- Dimensions (H x W x D): 1245 x 355 x 425 mm
- Minimum flow pressure: 2.5 bar
- Operating pressure: 2.5 to 5 bar
- Flow rate: 14-20 l/min
- Water inlet: 1 ¼” male
- Water outlet: 1 ½” male
- Electrical supply: 230 V – 50 Hz
Norms / Approvals
- EN 15154-2:2006
- ANSI Z358.1-2014
- DIN-DVGW, DVGW, NW-0417CL0263
- GOST-R, Certificate-No. 0615463 0615463
- GOST-TR-EX, Certificate-No. 0338358 0338358
The B-SAFETY eye-/face wash units with bowl and lid have been developed for use in industry. These eye showers are completely protected against contamination by the cover. The eye showers are activated by pulling down the cover. The size and design of the eye shower allows excellent localization even in emergency situations.
The eye shower is equipped with two jet regulators, which not only meet the requirements of DIN EN 15154-2:2006 and ANSI Z358.1-2014, but also ensure even water distribution. The limited, uniform and, above all, soft water jet is very suitable for rinsing out chemicals in the eye. Due to the limited water jet, the used water can be completely collected with this eye shower.
The correct jet height and desired flow rate are set on site via the integrated flow control valve. The eye shower is completely protected against dirt by the integrated hinged cover. This makes this shower the right solution for rough everyday industrial use. A sign for an eyewash device in accordance with DIN EN ISO 7010 with a viewing distance of 17 meters is attached to the cover.
- base plate with 4 mounting holes of stainless steel, polished, dimensions 200 x 200 mm
- stand pipe 1 ¼” of stainless steel, polished, with bottom water inlet 1 ¼” male
- housing, lid and bowl made of UV and impact resistant ABS plastics, water outlet 1 ½“ male
- integrated protective cover against dust
- actuation by pulling down the lid
- ball valve 3/8“ of stainless steel, with lever actuation by lid, DIN-DVGW tested and certificated
- aerators made of brass with a very limited spray pattern, chrome-plated
- with integrated flow regulation valve 3/8” for setting the desired spray height and flow rate, water inlet 3/8” male
- insulation made of mineral wool shape package, non-flammable, according to DIN 4102
- heating by self-regulating trace tape, output 12 W/m, electrical supply 230 V – 50 Hz
- outdoor thermostat and power-saving-circuit (shutdown of trace tape at 14°C, switch on at 4°C)
- outer casing of the shower made of screwed stainless steel housing, easy to dismantle for maintenance work, including green/white indicator strips for better visibility of the shower
- inclusive sign for eye shower according to EN ISO 7010 und ASR A1.3 on the lid, dimensions 170 x 170 mm, viewing distance 17 meter
- height 1245 mm, width 355 mm, depth 425 mm
- suitable for use in EX-Zones 1 & 2, all electrical parts explosion-proof, with risk assessment in accordance with industrial safety regulations concerning the non-electrical and electrical explosion protection
- according to BGI/GUV-I 850-0, DIN 1988 and DIN EN 1717
- according to ANSI Z358.1-2014 and DIN EN 15154-2:2006
- DIN-DVGW tested and certificated
Do you have questions or would you like advice?
You can reach us Monday to Thursday from 8 am to 5 pm and Friday from 8 am to 2 pm.
WE LOOK FORWARD TO YOUR MESSAGE
Do you have questions about how we can help your company? Send us an email and we’ll get in touch shortly.